Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'NT-JW Low Temperature Type'. Factory applied, grey coloured, two-component epoxy resin coating. Mix base and hardener in an 85:15 mass ratio and apply as per manufacturer's instructions. Cure for 17 hours@10°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Kubotaseal BM'. Factory applied, black coloured asphaltic bituminous coating. Apply as per manufacturer's PDS reference `11004T-1.4' dated Feb, 20, 2020. Cure 6 hours@20°C. For use with water up to 60°C. Materials listed in this section are not approved for use for contact with water that is required to be wholesome on large water retaining structures such as lining of pipes, cisterns or water storage tanks. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC3 Blue PTFE Coating'. Blue coloured, factory applied, PTFE coating intended to coat 'O' rings. Apply and cure as per manufacturer's instructions 'LDAP-007 issue 1' dated 11/02/2020. For use with water up to 85°C.
'Polyflon PTFE TC-7808-19 Grey PTFE Coating'. Factory applied, grey coloured PTFE coating. Apply as per manufacturer's technical data sheet dated 'June 8, 2012'. Cure for 20 minutes@380°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ET-52184 & ET-52185'. Factory applied, grey coloured water-based silicone coating comprising of an under-coat (ET-52184) and finishing coat (ET-52185). Apply as per manufacturer's instructions 'V8.2' issued January 2019. Cure for 10 minutes@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Luberpox-2K-DS-Lackfarbe IV80502 / IW 80 (Hardener) Blue Epoxy Coating'. Factory applied, blue coloured, two-component epoxy coating. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MORAPOX-WP'. Factory applied, two-part, red coloured epoxy coating comprising of a paint and hardener. Mix paint and hardener in a 2:1 volume ratio. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Conpipe Portland Cement Mortar NEN-EN 197-1 CEM II / A-LL 32,5 R'. Factory applied, grey coloured cementitious mortar lining. Mix cement and sand in a 1:1.1 mass ratio. Add water to cement in a mass ratio of 0.3-0.4. Cure for 28 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Conpipe Portland Cement Mortar NEN-EN 197-1 CEM I 42,5 N'. Factory applied, grey coloured cementitious mortar lining. Mix cement and sand in a 1:1.1 mass ratio. Add water to cement in a mass ratio of 0.3-0.4. Cure for 28 days@20°C. For use with water up to 60°C. This material is only approved for the mixing & curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JH C01'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'V7.2' issued January 2018. Cure for 15 minutes@200°C. For use with water up to 85°C.
Page 2 of 51
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
