Section Code 5311 :
Back To Directory Sections'Epcon C8 Extrem'. Site applied, grey coloured two-component epoxy resin anchor comprising of a resin and hardener which are supplied pre-mixed in a dispenser. Apply and cure as per manufacturer's instructions 'MAY-2020/EPCON C8_XTREM_GT'. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water.
'Chemfix CH+'. Grey coloured, two-component chemical anchor resin. Mix in a 10:1 volume ratio. Apply as per manufacturer's instructions dated 05/07/2014. Cure for 7 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PROV200'. Grey coloured, two-component chemical anchor resin. Mix in a 10:1 volume ratio. Apply as per manufacturer's instructions 'Rev 02/2020'. Cure for 7 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Timco Multi-Fix VESF'. Grey coloured, two-component chemical anchor resin. Mix in a 10:1 volume ratio. Apply as per manufacturer's instructions dated 25/09/2017. Cure for 7 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Anchor Pro Plus'. Grey coloured, two-component chemical anchor resin. Mix in a 10:1 volume ratio. Apply as per manufacturer's instructions 'rev 02-2020' dated '2019-10-15'. Cure for 7 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AT-HP/AT-HP Plus/S&P ResAC-19'. Grey coloured, two-component chemical anchor resin. Mix in a 10:1 volume ratio. Apply as per manufacturer's instructions dated 07/06/2018. Cure for 7 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Buffalo VYLSF 410'. Grey coloured, two-component chemical anchor resin. Mix in a 10:1 volume ratio. Apply as per Buffalo Product Data Sheet. Cure for 7 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘2KPS EX3’. Two-part epoxy resin anchor systems, available in light pink or grey colours, comprising of a resin and hardener. The systems are supplied in a pre-weighed (resin:hardener ratio of 3:1), two-component mixing cartridge. Cure 24 hours at 7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TCM 420PRO'. Grey coloured, two-component chemical anchor resin. Mix in a 10:1 volume ratio. Apply as per manufacturer's instructions version '18.08.2020'. Cure for 7 days@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘ChemSet™ REO502 EF PLUS, Epcon™ C6 EF PLUS & Epcon™ G5 PRO’. Grey coloured, two-part epoxy resin anchor systems, comprising of a resin and hardener. The systems are supplied in a pre-weighed (resin:hardener ratio of 3:1), two-component mixing cartridge. Cure 24 hours at 7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘JCP PURE EPOXY RESIN JF375E’. Two-part epoxy resin anchor systems, available in light pink or grey colours, comprising of a resin and hardener. The systems are supplied in a pre-weighed (resin:hardener ratio of 3:1), two-component mixing cartridge. Cure 24 hours at 7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘WCF-E3’. Two-part epoxy resin anchor systems, available in light pink or grey colours, comprising of a resin and hardener. The systems are supplied in a pre-weighed (resin:hardener ratio of 3:1), two-component mixing cartridge. Cure 24 hours at 7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 10'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '12/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Chemfix 600'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '11/11/2020'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘X-PRO 500’. Two-part epoxy resin anchor systems, available in light pink or grey colours, comprising of a resin and hardener. The systems are supplied in a pre-weighed (resin:hardener ratio of 3:1), two-component mixing cartridge. Cure 24 hours at 7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EX1'. Site applied, grey coloured (once mixed), two-component anchor resin. Mix, apply and cure as per manufacturer's product information 'EX1 V2.08' Issued '08/2021' (refer to working and loading times table for cure). For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘SMART S-IRE’. Two-part epoxy resin anchor systems, available in light pink or grey colours, comprising of a resin and hardener. The systems are supplied in a pre-weighed (resin:hardener ratio of 3:1), two-component mixing cartridge. Cure 24 hours at 7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Chemfix PESF TOP’. Site applied, grey coloured chemical anchor resin which is supplied in a pre-mixed cartridge. Apply as per manufacturer’s instructions 'Chemfix Polyester Styrene Free', rev. 1 dated 03/02/2022. Cure for 4 days@7°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Sika AnchorFix®-3030’. Two-part, grey coloured epoxy resin anchor system, comprising of a resin and hardener. The system is supplied in a pre-weighed (resin:hardener ratio of 3:1), two-component mixing cartridge. Cure 24 hours at 7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TCM585RE'. Red coloured chemical anchor resin supplied in a pre-weighed dual cartridge. Apply as per manufacturer's instructions dated '21.07.2021'. Cure for 48 hours@7°C. For use with water up to 23°C. For use only as a resin anchor having been tested at a reduced surface area to volume ratio of 1,000mm² per 1 litre of water. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 1 of 3
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
