Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'Eurokote® 48-20'. Factory applied, blue coloured, two component epoxy coating consisting of a resin and hardener. Mix resin and hardener in a mass ratio of 68:32 and apply as per manufacturer's TDS dated 10/12/2018. Cure for 24 hours@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS 1555'. Factory applied, dark blue/grey coloured vitreous enamel coating. Apply as per manufacturer's instructions 'I.PBE.06.04' dated November 22, 2021 and 'TPE.09.056.02' dated August 19, 2014. Cure for 14 minutes@850°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MasterSeal P693/94Primer and MasterSeal M 649 (formerly known as MasterSeal 694) Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply 'MasterSeal P693/94Primer’ as per Technical Data Sheet ‘MBS_CC-UAE/Sl_P_693/694_06_22’. Cure for 2 hours@25°C. Then mix and apply ‘MasterSeal M 649 Coating' as per Technical Data Sheet ‘MBS_CC-UAE/Sl_M 649_06_21/v1/08_21/v2/06_22/v3/10_22’. Cure for 1 minute@25°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Versathane'. Site applied, two-component, grey coloured (once mixed) polyurethane coating. Mix the grey coloured (opaque) base coating with the amber coloured hardener in a 3:1 volume ratio and apply Coat 1 as per manufacturer's product data sheet 'Issue No. 01 Sep 2016. Cure for 4 hours@7°C. Mix and apply Coat 2 using the same mix ratio and application instructions and then cure for 14 days@7°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘RTU AL 5023, RTU AL 5002A, RTU AL 5054, AL 8050, AL 8783 & AL 8062-1’. Factory applied, dark blue coloured enamel coatings. Apply as per manufacturer’s instructions version ‘11-2021’. Cure for 7 minutes@857°C. For use with water up to 85°C. These materials only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
`Scotchkote 206N`. Factory applied, green coloured, epoxy powder coating. Apply and cure as per manufacturer’s 'standard cure guide' which appears in document '80-6111-8352-8 Rev. B'. For use with water up to 23°C.
'SADIP-Mix'. Factory applied, grey coloured cement mortar. Mix sand, cement & water in a mix ratio of 2:1:0.5 and apply as per manufacturer's 'quality work instruction' document 'QW 41A', issue 4 dated 20/11/97. Cure for 24 hours@25°C. The cement mortar must then be submerged in water for 72 hours before use. For use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Klubertop TP 38-901’. Site applied, (transparent) white coloured PTFE lubricant coating. Apply and cure as per product information sheet ‘Prod. 099030, en-GB, Edition 12.05.2022’. For use with water up to 85°C.
'Deep Seal'. Factory applied, red-brown coloured (once mixed and applied), two-part polyurethane coating. Mix, apply and cure (full cure of 7 days@30°C) as per manufacturer's instructions ref. 'DI/PU/2022/072', dated 25/04/2022. For use with water up to 35°C.
'JDP21GEY‐5005, JDP21GEY‐5015 & JDP21GEY‐5017'. Factory applied, blue coloured, epoxy powder coatings. Apply as per manufacturer's Technical Data Sheet 'version 1.0', dated 15/02/2022. Cure for 20 minutes@180°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Purtop Easy DW'. Factory applied, two-component, cream coloured (once mixed and applied) polyurethane resin coating. Mix components A & B in a 4:1 volume ratio and apply as per manufacturer's TDS '7483-7-2021-I-gb'. Cure for 6 hours@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'EVER-SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2022.1.1', revision 'A2'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
'JSP-SRC'. Factory applied, grey coloured Sulphate Resistant cement. Mix cement and sand in a 2:1 mass ratio. Apply as per manufacturer's instruction sheet '2022.1.1', revision 'A2'. Steam cure for 8 hours@50°C. For use with water up to 65°C.
‘SIKALASTIC-836 DW & SIKAFLOOR 150’. Factory applied, off-white coloured (once mixed and applied), two-part polyurea coating system. ‘SIKAFLOOR 150’ is a two-component epoxy primer which is to be mixed in a 74:26 weight ratio and applied in accordance with manufacturer’s Product Data Sheet version ‘8’, dated May 2022. ‘SIKALASTIC-836 DW’ is a two-component polyurea coating which is to be mixed in a 1:1 volume ratio and applied in accordance with manufacturer’s Product Data Sheet version ’03.0’, dated January 2021. Cure for 24 hours at 25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote® 448 Bleu 5005 & Eurokote® 448 Bleu 5002'. Factory applied, blue coloured, two-part epoxy coatings consisting of a resin and hardener. Mix resin and hardener in a 1:1 volume ratio and apply as per manufacturer's technical data sheet version dated '29/08/17'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'S' epoxy powder coating. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions 'SNC-EP09V1 - date 2009/12/1'. Cure for 24 hours@30°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote 468 Thixo Brun Rouge'. Factory applied, red/brown coloured, two-part epoxy coating consisting of a resin and hardener. Mix resin and hardener in a weight ratio of 77:23 and apply as per manufacturer's Data Sheet dated '10/05/2019'. Cure for 10 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Relipoxy 342'. Factory applied, red coloured epoxy coating. Mix in a 3:1 weight ratio and apply in accordance with manufacturer's 'Standard Operating Procedure & Guidelines Revision 2' issue no. and date ;116/2021 15th Feb 2021'. Cure for 24 hours@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PPA 571 ES Blue 536'. Factory applied, blue coloured polyolefin coating. Apply as per manufacturer's instructions dated '08/2022'. Cure for 20 minutes@200°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 451 A – CP 573 B ITT Lowara'. Factory applied, blue coloured cationic resin coating. Apply as per manufacturer's technical data sheet 'LT/I-21-090' dated 'Sep 9, 2021'. Cure for 20 minutes@180°C. For use with water up to 50°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 10 of 26
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
