Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'PMSP5072-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PMSP5104-M'. Factory applied, blue coloured vitreous enamel coating. Apply as per manufacturer's instructions 'PEM 37 edition 01' dated '14/12/2020'. Cure for 5 minutes@840°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'42.5 (HSR)'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SW-02'. Factory applied, grey coloured cement mortar. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio. Cure for 24 hours@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Aquafitting Blue'. Factory applied, blue coloured epoxy coating. Apply and cure as per manufacturer's instructions file number 'DLCHB-CO-001', edition 'A1', issue date '2021-April-11st'. For use with water up to 65°C.
'Korepox H.B EH3100'. Factory applied, two component, cream coloured epoxy resin coating. Mix in a 3:1 volume ratio and apply as per manufacturer's instructions dated April 2009. Cure for 7 days@25°C. For use with water up to 40°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Ductan 087'. Factory applied, blue coloured PE coating. Apply by flock spray onto a part/item pre-heated to 200°C for 20 minutes and allow to cool. No cure required. For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOKIM Painting System'. Factory applied, dark green coloured (once top coat applied), two-component epoxy coating comprising of a primer and top coat. The primer (EPOX code A0768.N05133 + cat.A0918.N00100) consists of a catalyst and hardener which should be mixed in a 100:43 volume ratio before applying two coats in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 40 minutes@40°C. The top coat (EPOKIM HS code A0435.N02038 + cat.A0904.N00000) consists of a catalyst and hardener which should be mixed in a 100:16 volume ratio before applying one coat in accordance with instructions ‘W1_2021_00’ dated ‘25/10/2021’. Cure (flash-off) for 10 minutes@20°C. The complete system should then be ‘stoved’ for 60 minutes@70°C. For use with water up to 23°C.
'DUAYEN E-39'. Factory applied, two-component, red coloured (once mixed) epoxy coating. Mix Parts A&B in a volume ratio of 79.5:20.5 and apply as per manufacturer's instructions '00.05102021'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'ENDOPRENE®84-30 THIXO'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet (version dated 16/12/2019). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ENDOPRENE® 891.20 RACCORD'. Factory applied, cream coloured two-part polyurethane coating consisting of a resin and hardener. Mix and apply as per manufacturer`s technical data sheet 'Doc. 087' (version dated 01/07/2011). Cure for 48 hours at 20°C. For use with water up to 55°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'XFGJ-2'. Factory applied, grey coloured sulphate resistant cement. Mix cement:sand:water in a 1.5:1:0.4 mass ratio. Cure for 8 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Cepox P05/95'. Factory applied, two part, yellow coloured epoxy coating. Mix and apply as per Technical Data Sheet dated 19/11/2021. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'DAT-01'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a weight ratio of 34.4:44.9:20.7. Cure for 8 hours@50°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kerjiwal SRC'. Factory applied, grey coloured Sulphate Resisting Cement. Mix cement, sand & water in a volume ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'MS519'. Factory applied, blue coloured Porcelain Enamel coating. Apply as per manufacturer's instructions dated 2021.6.23. Dry for 2 hours@100°C before firing for 10 minutes@860°C For use with water up to 75°C. This material is only approved for the drying and firing conditions that appear on the approval. If the drying and/or firing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GMF-01'. Factory applied, grey coloured cement mortar. Mix sand, water & cement in a 1.5:1.0:1.0 weight ratio. Cure for 24 hours@25°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE OPC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE SRC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EARTHSTAHL TYPE BFSC'. Factory applied, grey coloured cement mortar. Mix cement, sand & water in a 1.0:1.5:0.5. Cure for 28 days@26°C. For use with water up to 50°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Tankguard 412'. White coloured, factory applied, 2 part epoxy coating. Mix and apply as per manufacturer's TDS dated 6 November 2015. Cure for 7 days@23°C. Between 1st November 2021 and 27th July 2022 this coating is for use with water up to 23°C. Between 28th July 2022 and 30th November 2026 this coating is for use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Powercron® 6070'. Factory applied, black coloured, electrodeposition coating. Apply and cure as per technical data sheet ‘LT/F-16-128’ dated October 20th 2016. For use with water up to 23°C.
'Flogul® 645 Vert 6013'. Factory applied, green coloured paint. Apply as per manufacturer's data sheet dated '11/09/2018'. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SDC)'. Factory applied, grey coloured, Sulphate Resisting Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-SIL)'. Factory applied, grey coloured Ordinary Portland Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JSAW-JAL (Cement-JSL)'. Factory applied, grey coloured Blast Furnace Slag Cement mortar. Mix cement, sand and water in a 1:1.5:0.5 weight ratio. Cure for 2 hours and 30 minutes@45°C and 85 relative humidity. Then cure again for 3 days@30°C and 80% relative humidity. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘PAM-MORTAR.D2'. Grey coloured (once mixed), factory applied Blast Furnace Slag Cement Mortar and admixture. Mix cement, sand, water & admixture in a mass ratio of 1:1.25:0.38:0.0008. Apply as per manufacturer’s technical data sheet dated 18/03/2021 (3rd revision) and cure for 48 hours@20°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Promag'. Factory applied, black coloured (once mixed), polyurethane primer and topcoat manufactured in Suzhou, China. Mix components A & B of the primer in a 1:2 mass ratio and apply as per manufacturer's instructions dated '13-01-2022' Cure for 2 hours@23°C. Mix components A, B & C of the topcoat in a 92.59%:5.19%:2.22% volume ratio and apply as per manufacturer's instructions dated '13-01-2022'. Cure for 20 seconds@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'V- SRPC Portland Cement'. Factory applied, grey coloured Portland Cement. Mixx Sand:water:cement in a weight ratio of 0.6:1.0:0.22. Cure for 96 hours@26°C and then 576 hours@32°C. For use with water up to 65°C.
'Tecnocoat P-2049'. Factory applied, two component, grey coloured polyurea coating. Mix components A & B in a weight ratio of 1:1 and apply as per manufacturer's TDS 'v. 20-03-2022'. Cure for 48 hours@23°C. Between September 2022 and August 2024, the coating is for use with water up to 23°C. From September 2024, the coating is for use with water up to 60°C. This material is only approved for the mixing, curing & soaking conditions that appear on the approval. If the mix/cure/soak conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Relipoxy 342 Food Grade Epoxy Coating'. Factory applied, brown-red coloured epoxy coating. Apply as per manufacturer's 'Standard Operating Procedure & Guidelines' issue number '116/2021' dated 15th Feb 2021. Cure for 24 hours@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Apcoguard SF 157'. Factory applied, grey coloured, two-component epoxy coating. Mix in a 3:1 volume ratio. Apply as per manufacturer's Application Guidelines 'APPPG/SF157/001' dated 'Jan-2021'. Cure for 7 days@25°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jerlac Two-Pack Epoxy Blue – 746 & Jerlac Two-Pack Epoxy Red – 747'. Factory applied, blue or red coloured, two-component epoxy coatings. Mix resin and hardener in a 3:1 volume ratio and apply as per manufacturer's instructions. Cure for 7 days@30°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`3M™ Scotchkote™ Fusion-Bonded Epoxy Coating 134`. Factory applied, green coloured, epoxy coating. Pre-heat substrate to 232°C, before dip coating as per manufacturer’s data sheet and application guide ‘78-8141-8528-2 Rev A’ dated February 2016, for 3 seconds. Cure for 10 minutes at 232°C. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. The following grades are manufactured at GERMANY, REUTLINGEN: Resicoat R4 blue: R4-ES HJ601R, R4-ES HJ605R, R4-ES HJ606R, R4-FB HJC04R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC12R, R4-FB HJC33R, R4-FB HJC34R, R4-FB HJC36R, R4-ES HJF01R, R4-ES HJF09R, R4-ES HJF10R, R4-ES HJF13R PAM blue, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF23R, R4-ES HJF24R, R4-ES HJF26R, R4-ES HJF42R, R4-ES HJG05R, R4-ES HJG07R, R4-ES HJG08R, R4-ES HJH01R & R4-FB HJC26R. Resicoat R4 red/red-brown: R4-FB HGC07R, R4-FB HGC17R, R4-ES HGF03R, R4-ES HGF04R, R4-ES HGF10R, R4-ES HGF17R, R4-ES HGF20R, R4-ES HGH02R. Resicoat R4 black: R4-ES HNF04R & R4-FB HNC01R. Resicoat R4 green: R4-FB HKC71R. Resicoat R8 blue: R8-ES HJF97R, R8-FB HJC37R, R8-FB HJC38R, R8-ES HJG13R, R8-FB HJC50R, R8-FB HJC51R, R8-FB HJC52R, R8-FB HJC53R, R8-FB HJC54R, R8-ES HJF1KR, R8-ES HJF2KR, R8-ES HJF3KR, R8-ES HJF4KR, R8-ES HJF5KR, R8-ES HJF6KR, R8-ES HJG29R & R8-ES HJ609R. Resicoat R8 blue grades added in July 2024: R8-FB HJC55R, R8-ES HJF4MR & R8-ES HJF5LR. Resicoat R8 red/red-brown: R8-FB HGC12R, R8-ES HGF66R, R8-ES HGF67R & R8-ES HGF68R. Resicoat R8 red added in February 2025: R8-ES HGF65R. Resicoat R8 black: R8-ES HNC03R & R8-ES HNF43R. Resicoat R2 blue: R2-ES HJF5BR & R2-ES HJF4ER. The following grades are manufactured at USA, NASHVILLE: Resicoat R4 blue: R4-ES HJ606R, R4-ES HJF10R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-FB HGC17R & R4-ES HGF17R. Resicoat R4 green: R4-ES HKF47R. The following grades are manufactured at CHANGZHOU, CHINA: Resicoat R2 blue: R2-ES HJF5BR. Resicoat R4 blue: R4-FB HJC03R, R4-FB HJC06R, R4-FB HJC08R, R4-FB HJC15R, R4-FB HJC23R, R4-FB HJC29R, R4-ES HJF01R, R4-ES HJF10R, R4-ES HJF13R, R4-ES HJF14R, R4-ES HJF22R, R4-ES HJF24R & R4-ES HJF42R. Resicoat R4 red/red-brown: R4-ES HGF03R, R4-ES HGF04R & R4-ES HGF17R. Resicoat R4 black: R4-ES HNF04R. Resicoat R8 blue grades added in February 2025: R8-FB HJC50R, R8-ES HJF3KR, R8-ES HJF97R The following grades are manufactured at IZMIR, TURKEY: Resicoat R2 blue: R2-ES HJF3D4 & R2-ES HJF4D4. Resicoat R4 blue: R4-ES HJF1C4 & R4-ES HJF2C4. Resicoat R8 blue added in February 2025: R8-ES HJF5M4 The following grades are manufactured at THANE, INDIA: Resicoat R2 blue: R2 HJC43N, R2 HJF2HN, R2 HJF5BR. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'35000 Kanpoly Purco'. Factory applied, two-component, blue coloured, solvent-free polyurethane based coating. Mix and apply as per manufacturer's instructions '0141', 'revision 02' dated February 2022. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Polyurea FA 1044'. Factory applied, two-component, beige coloured polyurea coating. Mix parts A and B in a 1:1 volume ratio apply as per manufacturer's TDS '07/2015 Rev.00'. Cure for 96 hours@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotapipe AC1003XT'. Factory applied, green coloured fusion bonded epoxy coating. Apply as per manufacturer's TDS dated 8 June 2021. Cure for 5 minutes@235°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Resicoat factory applied, epoxy powder coatings. The coatings are electrostatically applied by spray onto a panel pre-heated for 15 minutes@225°C and then post cured for 15 minutes@220°C. For use with water up to 85°C. Resicoat R4 blue R4-FB HJC06R & R4-ES HJF26R. Resicoat R4 red/red-brown R4-ES HGF03R. Resicoat R4 black R4-FB HNC01R. Resicoat R4 black: R4-ES HNF04R.
‘PVEF undercoat with Fluiglide Topcoat’. Factory applied, cream coloured (once mixed and applied), coating system comprising of ‘Polyglass VEF’, two-component glassflake vinyl ester undercoat and ‘Fluiglide’, two-component polyester topcoat. Mix and apply ‘Polyglass VEF’ in accordance with Corrocoat ‘product reference 2/23’ dated ‘5th June 2007’ and last reviewed ‘March 2022’. Cure for 24 hrs@20°C (±1°C). Mix and apply ‘Fluiglide’ in accordance with Corrocoat ‘product reference ‘4/01’, valid from ‘23rd October 1995’ and last reviewed ‘March 2022’. Cure for a minimum of 6 days@20°C (with a lower tolerance of -1°C). These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'QY031E'. Factory applied, blue coloured epoxy powder coating. Pre-heat the substrate to 250°C and then apply the coating at a temperature of 160°C as per manufacturer's product specification 'QY031E-01' dated '2022-3-23'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the application and curing conditions that appear on the approval. If the application and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GTH-CC Iron Red'. Factory applied, two-component, red coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'GTH-CC Ice Grey'. Factory applied, two-component, white coloured epoxy coating. Mix parts A & B in a 20:4 mass ratio. Apply as per manufacturer's painting guide '202105006' dated 'May 27, 2021'. Cure for 21 days@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Lacaze Radiant'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RC851'. Factory applied, two part, yellow coloured epoxy coating. Mix parts A & B in a 100:26 weight ratio and apply as per Technical Data Sheet 'NT-0229-UK-201109-C' dated 11/05/2022. Cure for 16 hours@70°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Tianbao SS Epoxy Coating'. Factory applied, two-component white coloured epoxy coating. Mix component 1 and component 2 in a mass ratio of 6:1 and apply as per manufacturer's operation in instructions 'Tianbao SS', 'version 1.0' issued on '06/02/2021'. Cure for 7 days@25°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epigard DT High Build Finish Epoxy Coating'. Factory applied, two-component, grey coloured epoxy coating. Mix and apply as per manufacturer's instructions ‘Document Ref : SPL/R&D/TTD/UI/001, Issue No.01, Version: 01’ dated 01.11.2015. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Kejriwal OPC’. Factory applied, grey coloured in-organic, Ordinary Portland Cement mortar. Mix cement, sand & water in a mass ratio of 1:1.2:0.5. Cure for 28 days@32°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Epilux QD Exterior Coating'. Factory applied, blue coloured, two-component epoxy coating comprising of a base and accelerator. Mix base and accelerator in a 3:1 volume ratio and apply as per manufacturer's data sheet '679', dated 'Jun 2020'. Cure for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Eurokote® 47-20 Brun Rouge'. Factory applied, red coloured (once mixed and applied), two-component epoxy coating. Mix resin and hardener in an 80:20 mass ratio and apply as per manufacturer's instructions dated '15/06/2021'. Cure for 7 days@20°C. For use with water up to 60°C. his material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 3 of 11
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
