Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'Welmortar-SRP'. Factory applied, grey coloured cement mortar. Mix sand:cement:water in a 3:2:1 weight ratio and apply as per manufacturer's SOP document 'WDIPL/QA/WI/14C', revision '1', dated '08.02.2023'. Cure for 28 days@30°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘LUBERPOX-2K-DS-Lackfarbe, Verkehrsblau IV80517’ & ‘LUBERPOX-2K-DS-Lackfarbe, Signalblau, IV80505’. Factory applied, blue coloured, two-component epoxy coatings. Mix and apply in accordance with Technical Data Sheet rev. 37 dated 25.05.2020 . Cure for 7 days@23°C. For use with water up to 65°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Resicoat RS Redbrown & Blue'. ‘Resicoat RS 506530’ (blue coloured) was added to the approval in December 2024. Factory applied, two component, redbrown or blue coloured epoxy coatings. Mix in a ratio of 2:1 and apply as per product sheet 'revision no. 4' dated 'May 11, 2023'. Harden for 24 hours@23°C. For use with water up to 60°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'RAX Cement Mortar'. Factory applied, grey coloured cement mortar. Mix cement:sand:water in a 1:1.5:0.6 weight ratio and apply as per manufacturer's work instructions 'WI-PRD-08', rev. '00', dated '01.02.2023'. Cure for 24 hours@28°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Valcoat Blue'. Factory applied, blue coloured epoxy coating. Pre-heat the substrate and apply as per manufacturer's TDS with issue '01.04.2023'. Post-cure for 5-7 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'TM-cement-01'. Factory applied, grey coloured cement. Mix sand/cement/water in a weight ratio of 1.7:1.0:0.74 and apply as per manufacturer's instructions 'TM20231122-A0', dated 2023-11-22. Cure for 6 hours@25°C (±2°C). Between November 2023 and November 2024, the material was for use with water up to 23°C. Between December 2024 and November 2028, the material is for use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JDFF epoxy powder coating’. Factory applied, blue coloured fusion bonded epoxy coating. Apply as per manufacturer`s instructions (Procedure #: Pc-01-3, Work Instruction #: JDFF WI-Pc-01-3-1, Revision #: 2, Issue #: 5, date: 10-01-2023). Cure for 2½ minutes at 232°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'Cleantech PW'. Factory applied, two-component, red coloured epoxy coating. Mix component A and component B in a volume ratio of 3:1 and apply as per manufacturer's product data sheet 'CCPL/TDS/R11/CRC/17-18/04/R6/spray'. Cure for 7 days@27°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Pipeclad 704G'. Factory applied, green coloured fusion bonded epoxy powder coating. Apply as per manufacturer's Product Information '704G_TDS', revised 'August 16,2022'. Post-cure for 12 minutes@232°C. For use with water up to 85°C. This material is only approved for the post-curing conditions that appear on the approval. If the post-cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'KAJ1207'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instructions reference 'XA12312', dated 26/12/2022. Cure for 15 minutes@220°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'PPA571ES Black 700 & PPA571 Black 700'. Factory applied Polyolefin PE Coatings. Apply 'PPA571 Black 700' by fluidised bed according to manufacturer's data sheet '08/2022' and dip in the bed for 5-8 seconds. Apply 'PPA571ES Black 700' by electrostatic spray according to manufacturer's data sheet '08/2022'. Cure for 190-200°C for 20 mins. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL035P Interpon 100 Gloss Light Grey'. Factory applied, light grey coloured epoxy coating. Apply as per manufacturer's Product Data Sheet 'Interpon 100 -AL035P - Issue #01', revision date '20.07.2021'. Cure for 10 minutes@180°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'CY7000 Blue'. Factory applied, blue coloured epoxy coating. Apply as per manufacturer's instruction manual 'YS-QNS-WZBC-2021W', dated 'May 20, 2021'. Cure for 15 minutes@180°C. For use with water up to 40°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'C21 Dyopox PTW White'. Factory applied, two-part, creamy white coloured epoxy resin coating. Mix base and hardener in a mass ratio of 4:1 and apply as per manufacturer's TDS dated '2011'. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Klubertop TP 38-901’. Site applied, (transparent) white coloured PTFE lubricant coating. Apply and cure as per Kluber Lubrication product information sheet ‘Prod. 099030, en-GB, Edition 12.05.2022’. For use with water up to 85°C.
'68093X'. Factory applied, blue coloured epoxy powder coating. Apply per manufacturer's instructions 'V2.3' dated March 2018. Cure for 20 minutes@200°C For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Kinlin Epoxy Power Coating (Green colour, EPX‐111A)'. Factory applied, green coloured epoxy powder coating. Apply as per manufacturer's instructions 'XL-R-019-G1' dated '2018-9-21'. Cure for 10 minutes@180°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Relithane 151. Factory applied, brown coloured, two-component Polyurethane coating. Mix base and hardener in a 2.5:1 ratio and apply as per manufacturer's 'Standard Operating Procedure & Guidelines, Revision 2, 157/2022' dated 12th October 2022. Cure for 40 seconds@35°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'AL 8423'. Factory applied, dark blue coloured enamel coating. Apply as per manufacturer's TDS '08423', version '02-2024' and cure for 7 minutes@860°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
Page 17 of 26
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
