Section Code 5030 : Factory applied pipe & fittings coatings.
Back To Directory Sections'Unitech DIP Sulphate Cement'. Factory applied, grey coloured sulphate cement. Mix as per work instructions issue no. 'QAP-MOS-UNITECH 212-13- rev1', dated 21st December 2020. Cure for 6 hours@40°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JIZJ-2'. Factory applied, grey coloured Sulphate resistant Portland cement. Mix cement, sand & water in a 1:1.7:0.55 mass ratio. Cure for 5.5 hours@65°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'BGDI01 Sulphate Resistant Cement & BGDI02 Portland Cement'. Factory applied, grey coloured cements. Mix 1 part cement, 2 parts sand and 0.25 parts water. Cure for 10 hours@23°C. For use with water up to 65°C. These materials are only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'PMSP5105-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'PMSP5065-M'. Factory applied, blue coloured Vitreous Enamel coating. Apply and cure as per user instructions reference 'PEM 37' dated '14/10/2020'. For use with water up to 85°C.
'Parasakti Sulphate Resisting Portland Cement'. Factory applied, grey coloured Sulphate Resistant cement mortar. Mix cement, sand and water in a 1: 1.5: 0.5 ratio. Cure for 28 days@5°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Rashmi Cement 43 Grade OPC'. Factory applied, grey coloured Ordinary Portland cement mortar. Mix cement, sand and water in a 1: 1.5: 0.5 ratio. Cure for 28 days@5°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'LSR Soft Touch Coating – Kohler NC001'. Factory applied, three-component, clear silicone coating. Mix coating, catalyst and thinner in a 100:2:500 mass ratio, stir for 10 minutes and then apply. Cure for 10 minutes@160°C, humidity 60%. For use with water up to 70°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'MEKCOAT Liquid Membrane Coating'. Factory applied, two-component, blue coloured polyurethane coating. Mix in a 1:1 volume ratio. Cure for 24 hours@23-24°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'5017 Blue'. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions issued January 2020, 'V7.2'. Cure for 15 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'JH'. Factory applied, blue coloured epoxy powder coating. Heat substrate to 220°C for 30 minutes, spray apply coating and then cure at 190°C for 20 minutes. For use with water up to 23°C. This material is only approved for the application and curing conditions that appear on the approval. If the cure and/or application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘EUROKOTE® 46-20’. Factory applied, red-brown coloured, two-part epoxy resin coating. Mix and apply as per manufacturer's technical data sheet 'Doc. 087' dated 01/07/2011. Cure for 7 days@20°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Electroline ES 1212-Black`. Factory applied, black coloured, 2 part epoxy coating. Mix parts A&B in a 3:1 volume ratio. Cure for 7 days@30°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
‘SIGMAPRIME 200 for use with SIGMAGUARD CSF 585 (white) or SIGMAGUARD CSF 585 (blue)’. Factory applied, white or blue coloured (once mixed and applied), two-part epoxy coating comprising of Coat 1 and Coat 2. SIGMAPRIME 200 (Coat 1) comprises of a base and hardener to be mixed in a 80:20 volume ratio. Cure for 3 days@23°C. SIGMAGUARD CSF 585 (white) or SIGMAGUARD CSF 585 (blue) is to be applied as Coat 2 and each comprises of a base and hardener to be mixed in a 77.5:22.5 ratio. Cure for 12 days@23°C. For use with water up to 23°C.
`R2 Red & R2 Blue`. Factory applied epoxy powder coatings manufactured in Changzhou. Apply as per manufacturer's instructions for use 'ANCZ-RAD-W501', 'revision no: 2' dated 'May. 5th 2021'. Cure for 10 minutes@200°C. For use with water up to 80°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Jotaguard VA 5001 Blue`, factory applied, blue coloured, fusion bonded epoxy coating. 'Jotaguard VA 5001 Red`, factory applied, red coloured, fusion bonded epoxy coating was added to the approval in June 2023. Apply both coatings as per Jotun Technical Data Sheet issued 9th November 2015. Cure for 5 minutes@245°C. For use with water up to 85°C. These materials are only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the materials are not covered by the scope of the approval.
'Kubotapowder TK1413F'. Factory applied, grey coloured epoxy resin coating. Apply as per manufacturer's instructions 'GR-294E' dated 2018/10/01. Cure for 20 minutes@180°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'WB-108'. Factory applied, two-component, grey coloured epoxy coating. Mix, apply and full cure (7 days@20°C) as per manufacturer's technical data sheet 'file no. TWJ-WB-108', 'edition: A1' dated 01/12/2020. For use with water up to 65°C.
'Epoxy phenolic FBE-4 RAL 5010'. Factory applied, blue coloured epoxy phenolic coating. Apply as per manufacturer's instructions dated '11/20'. Cure for 10 minutes@200°C. For use with water up to 85°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPOXY TB BT Grey RAL 7016'. Factory applied, grey coloured, fusion bonded epoxy coating. Apply as per Technical Data Sheet 'document version:1' dated 'June 22, 2021'. Cure for 10 minutes@160°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
‘Karumel EX4412 Blue & Grey’. Factory applied, blue or grey coloured, epoxy resin based powder coating. Apply and cure as per manufacturer’s instructions reference 'PCA-21062901', issued August 2021. For use with water up to 85°C.
`3011 high chlorinated polyethylene anticorrosive coating`. Factory applied, burgundy coloured polyethylene coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18 2020. For use with water up to 23°C.
'DELTAPrime 2K SF Primer and DELTAShield HP 500 PW Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply DELTAPrime 2K SF Primer as per Product Data Sheet ‘October 2019-001’. Cure for 2 hours@25°C. Then mix and apply DELTAShield HP 500 PW Coating as per Product Data Sheet ‘190625’. Cure for 1 minute@25°C. For use with water up to 85°C.
'H-453'. Factory applied, grey coloured ceramic epoxy coating. Apply as per Technical Data Sheet file no. 'TWJ-H-453', edition 'A2', dated '01/03/2020'. Cure for 5 days@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`9011 Epoxy anticorrosive coating`. Factory applied, black coloured epoxy coating. Apply and cure as per manufacturers `IFU Version no. 03' dated June 18, 2020. For use with water up to 23°C.
'KINTE Epoxy Resin Coating (ES-BL10724-S9)'. Factory applied, blue coloured coating. Apply and cure as per manufacturer's instructions issued 'March 2018 V5.2'. For use with water up to 85°C.
'FY-6 (white coloured) & FY-5 (blue coloured)'. Factory applied epoxy powder coatings. Apply and cure as per manufacturer's instructions ‘fyzj2020925 version 1' dated '2020-9-20'. For use with water up to 85°C.
'GP HBSL EPOXY'. Factory applied, brown coloured epoxy coating. Mix and apply as per manufacturer's standard operating procedure document number 'GP/SOP/HBSL/001', version '01' dated 1st April 2019. Cure for 17 days@30°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
`Jotaguard VA 5001`. Factory applied, dark blue coloured fusion bonded epoxy coating. Apply and cure as per manufacturers test method document no. '39.40.014', issue date '02.01.2018', revision no. '02'. For use with water up to 85°C.
`POWLAC EY161`. Factory applied, blue coloured epoxy powder coating. Apply as per manufacturer's instructions `no. CKP-2015-0172`. Cure for 5 minutes@180°C. For use with water up to 85°C. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Global Smart (INSUPIPE)'. Factory applied, grey coloured cement. Mix cement:sand:water in a 30:55:15 ratio. Cure for 48 hours@25°C. For use with water up to 85°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'ELASTOPOXY PRIMER HP and ELASTOSEAL W Coating'. Factory applied, grey coloured (once mixed), two-component primer (non-water contact primer) and two-component coating (water contact coating). Mix and apply 'ELASTOPOXY PRIMER HP as per Product Data Sheet ‘TSS/TD/280721/C’. Cure for 2 hours@25°C. Then mix and apply ‘ELASTOSEAL W Coating’ as per Product Data Sheet ‘TSS/TDS/260721-B’. Cure for 1 minute@25°C. For use with water up to 85°C.
'Ductan 087'. Factory applied, blue coloured PE coating. Apply by flock spray onto a part/item pre-heated to 200°C for 20 minutes and allow to cool. No cure required. For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SYI-03'. Factory applied, grey coloured, Portland cement mortar. Mix cement, sand and water in a mass ratio of 1:1.5:0.6. Cure for 4 hours@23°C. For use with water up to 65°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mix and/or cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Neropoxy Solvent Free Coating White & Red'. Factory applied, white or red coloured, two-component epoxy coating comprising of a base and hardener. Mix base and hardener in a 3:1 mass ratio. Cure for 10 days@28°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'QuickSpray Industrial W coating for use with Quick Prime primer'. Factory applied, blue coloured coating system comprising of a primer and topcoat. ‘Quick Prime’ is a two-component epoxy primer. Mix parts A & B in a 1:2 volume ratio and cure for 4 hours@20°C. ‘QuickSpray Industrial W’ is a two-component elastomeric topcoat. Mix parts A & B in a 1:1 volume ratio, apply over the primer and then cure for 24 hours@20°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'PPA 801 Blue 502'. Factory applied, grey coloured modified PE blend coating. Pre-heat part/item to be coated to 340°C, dip into a fluidized bed containing the coating and then allow to cool at room temperature. No cure required For use with water up to 23°C. This material is only approved for the application conditions that appear on the approval. If the application conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Nu Vista'. Factory applied, grey coloured Portland Slag Cement. Mix water, sand and cement in a mass ratio of 1:2:3. Cure for 1.5 hours@30°C, then 4 hours at 45°C and then 28 days (672 hours)@35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'TML Dalmia Infra Pro'. Factory applied, grey coloured Portland Slag Cement. Mix water, sand and cement in a mass ratio of 1:2:3. Cure for 1.5 hours@30°C, then 4 hours@45°C and then 28 days (672 hours) @35°C. For use with water up to 60°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPX-111'. Blue coloured, factory applied epoxy powder coating. Apply and cure as per manufacturer's instructions XL-R-019-R1 dated 2015-11-12'. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified then the material is not covered by the scope of the approval.
'ColorDur T300 EPOXY SF Coating - Red' & 'ColorDur T300 EPOXY SF Coating - Grey' (grey was added to approval in August 2022). Factory applied, two-component, red or grey coloured epoxy coating. Mix resin and hardener in a 3:1 volume ratio. Cured for 7 days@30°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EPX-213H Grey'. Factory applied, grey coloured, epoxy powder coating. Apply and cure as per manufacturer's instructions 'XL-R-019-R2' dated '2015-11-12'. For use with water up to 85°C.
'KD-002'. Factory applied, blue coloured powder coating. Apply and cure as per manufacturer's instructions file number 'KD-1230-20', version 'A0', dated '2020-12-30'. For use with water up to 23°C.
'SC2 Coating'. Factory applied, clear, PTFE based coating. Apply and cure as per manufacturer's instructions 'LDAP-002 issue 1' dated 09-08-2016. For use with water up to 85°C.
'Protecfull SFP 108'. Factory applied, two-component, cream coloured polyurethane coating. Mix part A & part B in a 75:25 volume ratio and apply as per manufacturer's instructions reference '016. Ed.01.21' dated August 24, 2021. Cure for 7 days@23°C. For use with water up to 23°C. This material is only approved for the mixing and curing conditions that appear on the approval. If the mixing and/or curing conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'Hempaline Defend 630 Cure 72'. Factory applied, white coloured, two-component epoxy coating. Mix base and curing agent in a 3:1 volume ratio and apply as per manufacturer's product data sheets dated June 2021, Cure for 6 days@20°C. For use with water up to 60°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'EP-I-103'. Factory applied, blue coloured fusion bonded epoxy coating. Apply and cure as per manufacturer's instructions issue 'EPOXY86315', dated 'Nov. 15th, 2020'. For use with water up to 65°C.
'Rilsan (MagnaCoat 5501 F)'. Factory applied, white coloured (opaque), polyamide powder coating. Apply as per manufacturer's instructions dated 02/01/2018. Cure for 10 minutes@230°C. For use with water up to 65°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'FIBER TECH 80, Low VOC fiberglass resin'. Factory applied, brown coloured polyester resin & fibreglass. Apply as per manufacturer's method statement reference 'PP-GRP-092021-R1' dated '21 Sept. 2020'. Cure for 48 hours@25°C. For use with water up to 23°C. This material is only approved for the curing conditions that appear on the approval. If the cure conditions are varied from those specified on the approval then the material is not covered by the scope of the approval.
'SC1 Coating'. Factory applied, clear, PTFE based coating. Apply and cure as per manufacturer's instructions 'LDAP-001 issue 1' dated 09-08-2016. For use with water up to 85°C.
Page 2 of 11
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
