Drain cock elbow incorporating a DZR brass body with EPDM ’O’-rings (ZELB250445 model) or NBR ‘O’-rings (ZELB250446 model added July 2022). Both models are for use with copper pipe (manufactured to BS EN 1057). Maximum working pressures: ZELB250445 model - 10.0 Bar. ZELB250446 - 16.0 bar. Maximum operating temperature 85°C.
Range of combined thermal balancing and pressure reducing valves with gun metal bodies, stainless-steel strainer, pressure gauge and temperature gauge. Maximum inlet supply pressure 16.0 bar. Outlet pressure range of 1.5 bar – 5.5 bar. Maximum operating temperature 85°C.
Range of polypropylene push-fit fittings and inserts for use with MDPE pipe (manufactured to BS EN 12201). For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Range of polypropylene push-fit fittings with inserts for use with MDPE Pipe (manufactured to BS EN 12201-2) on one side of the fitting and PB (BS 7291), PEX (BS 7291) or Copper (BS EN 1057) on the other. Models UTS147-DB, UTS197-DB & UTS251-DB are for above and below ground use. All other models are for above ground use only. Maximum working pressure when using 20mm pipe is 16.0 bar. Maximum working pressure when using 25mm & 32mm pipe is 12.5 bar. Cold water use only.
Range of flow switches with brass bodies incorporating EPDM ‘O’-rings, acting as a leak detection system that actuates an integral spherical valve to shut off the water supply. The inlet incorporates a stainless steel strainer. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 16.0 bar. Maximum operating temperature 30°C.
‘Ausimix’ compact range of ‘T’-type thermostatic blending valves with nickel plated DZR brass bodies. Each inlet incorporates a stainless-steel strainer and a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The SBHEAT110780, SBHEAT110785, HEAT110780 & HEAT110785 models also have angled isolation valves at both inlets. Maximum working pressures and operating temperatures: Existing push fit models: For use with PEX pipe (manufactured to BS7291 part 3) and Polybutylene pipe (manufactured to BS7291 part 2): 12.0 bar, cold water use only. 6.0 bar @ 95°C. For use with copper pipe: Maximum working pressure 10.0 bar. Maximum operating temperature 95°C. Compression models added October 2023: For use with copper pipe to BSEN1057:2006: Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
T-type mixing valve with a DZR brass body (nickel plated), temperature is controlled by a thermostatic cartridge. Each inlet incorporates a combined EPDM washer and stainless steel strainer, and a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). For use with copper pipe manufactured to EN1057. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
T-type mixing valve with a DZR brass body (nickel plated), temperature is controlled by a thermostatic cartridge. For use with copper pipe manufactured to EN1057. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Range of cold water inlet control groups with DZR brass bodies, consisting of a pressure reducing valve, (all models are adjustable between 1.0 and 6.0 bar, but some come pre-set from the factory - see model), a pressure relief valve (set at 6.0 or 8.0 bar - see model) and a single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). The pressure relief valve is fitted with a rotary type easing gear. All products for use with copper pipe manufactured to BS EN 1057. Maximum inlet supply pressure 20.0 bar. Cold water use only.
Range of multi-layered flexible hoses (TPE inner liner/PVC middle/PVC outer with polyester braiding in-between) and stainless-steel braided EPDM flexible hoses. The hoses are supplied with a variety of end connections incorporating brass barbed hose inserts or white plastic barbed hose inserts. The hoses may also incorporate a servicing valve (see model). The push fit connectors are to be used with copper pipe (Manufactured to EN1057), PB pipe (Manufactured to BS EN21003) & PE-x pipe (manufactured to BS EN7291-3). Products shown with a “P” suffix (eg. WFLX15P, FLX43P) are a prepacked variant of the original product eg. WFLX15, FLX43. Products shown with a “SB” suffix (eg. FLX15P-SB, WFLX28-SB) are a reduced box quantity of an existing product. Maximum working pressure and operating temperature: 12.0 bar @ 20°C and 6.0 bar @ 65°C.
Page 2 of 8
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.