Section Code 2240 : Solenoid, plastic.
Back To Directory SectionsRange of servo-controlled and normally closed (NC) solenoid valves with various plastic bodies and various inlet / outlet options. Inlets incorporate stainless steel strainers. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C
Range of solenoid valves with plastic bodies and silicone diaphragms. The outlets incorporate a plastic flow restrictor. Maximum working pressure 10.0 bar. Cold water use only.
Solenoid valve with plastic body and silicone rubber diaphragm. Maximum working pressure 0.03 bar. Maximum operating temperature 65°C
Servo assisted, normally closed solenoid valve with a plastic body and EPDM membrane. The inlet incorporates a stainless-steel strainer. Maximum working pressure 10 bar. Cold water use only
Ranges of solenoid valves with plastic bodies, incorporating EPDM ‘O’-rings and diaphragms. Models also incorporate a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only. From September 2020, the maximum operating temperature is 90.0°C
Range of normally closed (monostable) and pulse controlled/latching (bistable) solenoid valves with plastic bodies, integral stainless steel strainer, From September 2023 the 50.005.101 model can also be supplied with an integral plastic strainer. EPDM diaphragm, EPDM ‘O’-rings and seals. To be installed in specifically dimensioned bodies. The 50.005.101 model can be supplied with or without a brass adaptor. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Normally closed solenoid valve with a plastic body and EPDM diaphragm. Maximum working pressure 8.0 bar. Maximum operating temperature 85°C.
Range of plastic bodied normally closed latching solenoid valves. The 42424000 model is supplied with an additional brass housing. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Non latching solenoid valve with a plastic body and an EPDM gasket and ‘O’-ring. Maximum working pressure 8.0 bar. Cold water use only.
Solenoid valves with a plastic body and silicone diaphragm and ‘O’ rings. Maximum working pressure 8.0 bar. Cold water use only.
Range of normally closed solenoid valves with a plastic body and silicone rubber diaphragm & ‘O’-rings. Models ending ‘007’ have a maximum working pressure of 0.25 bar. All other models have a maximum working pressure of 0.06 bar. Maximum operating temperature 90°C.
Range of bistable (all models) or monostable/normally closed (19.00x.287 only) solenoid valves with either a plastic body (19.00X.287) or plastic internal body with stainless steel threaded casing (50.005.102 and 50.005.(050) models) with EPDM diaphragms and ‘O’-rings. Maximum working pressures: 50.005.(050) model: 8.0 bar. All other models: 10.0 bar. Maximum operating temperature 70°C
Solenoid valve with plastic body and silicone rubber diaphragm. Maximum working pressure 0.18 Bar. Cold water use only.
Range of solenoid valves with plastic bodies and EPDM diaphragms. The inlet incorporates a plastic strainer and an integrated flow meter sensor. Both the inlet and the outlet incorporate a white plastic flow restrictor. The products are also supplied with an optional EPDM outlet gasket, for installation over the outlet spigot. Maximum working pressure 10.0 bar (to diaphragm). Maximum operating temperature 85°C.
Range of plastic bodied solenoid valves incorporating a stainless steel spring and armature with an EPDM diaphragm. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of normally closed and normally open plastic solenoid valves with EPDM ‘O’-rings and sealing rings. Pushfit connections for use with John Guest LLDPE pipe or copper pipe. The 47.004.103 model acts as a diverter between two outlets, where one outlet is always open. Maximum working pressures see model section. Maximum operating temperatures: 65°C - 47.00X.1XX models with John Guest LLDPE pipe only. 90°C - 47.004.103 model with John Guest LLDPE pipe only. Models added January 2021: Cold water use only - 47.00X.2XX (4mm & 8mm) with John Guest LLDPE pipe only. 90°C - 47.00X.2XX (6mm) with John Guest LLDPE pipe only. 90°C - 47.00X.2XX (6mm & 8mm) with copper pipe only.
Aquatsop leak detection system intended to shut the water supply in the event of a water leak. Consisting of two single normally closed servo controlled solenoid valves with a flow regulator and stainless steel filter at the inlet. A LDPE inner hose with corrugated plastic outer hose. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.
Range of latching and normally closed (see model) solenoid valves with plastic bodies, NBR diaphragms and ‘O’-rings. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C
Solenoid valve incorporating a plastic body and an EPDM diaphragm. The product incorporates a plastic flow regulator with an EPDM washer, and a plastic filter on the inlet. Maximum working pressure 10.0bar. Maximum operating temperature 60°C.
Solenoid valve with a plastic body, EPDM membrane and plastic or stainless steel strainer. From March 2023 the product may also be supplied with a Ø 28.61mm x ¾” BSP (M) plastic adaptor. From December 2023 the product may also be supplied with a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.
Non-metallic materials and components comply with BS6920 at 70°C
Range of solenoid valves with a plastic body and an EPDM diaphragm. Available as either inline (126 suffix models) or 90° outlet (115 suffix models). The inlet of the existing 62.009.115 (¾” BSP (M) inlet x ⅜” BSP (M) outlet) model incorporates a plastic strainer and a plastic flow regulator. The products are also supplied with an optional stainless-steel strainer for installation on the inlet. Maximum working pressure 10.0 bar. Maximum operating temperatures: Existing model 62.009.115: ¾” BSP (M) inlet x ⅜” BSP (M) outlet: 90°C. Models added November 2023: Cold water use only.
Plastic bodied solenoid valve available as both a latching and normally closed variant, with an EPDM diaphragm and ‘O’-rings. Maximum working pressure 6.0 bar. Maximum operating temperature 65°C.
‘1175B’ range of servo-controlled normally closed (NC), normally open (NO) or latching solenoid valves with off-white nylon bodies, incorporating a NBR diaphragm with POM diaphragm inserts. For use with copper tube manufactured to EN1057 or John Guest Speedfit barrier pipe manufactured to BS7291 part 3. Maximum working pressure 10.0 bar. Cold water use only.
Range of latching and non-latching solenoid valves with a plastic body (all models, except for 07230017 & 07230018 models added September 2023) and an EPDM diaphragm. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Premix control unit for an infrared sensor tap comprising of a solenoid valve with plastic body, EPDM diaphragm and ‘O’-rings, and silicone seals. Both the cold and hot inlets incorporate an approved single check valve cartridge, however the complete assembly has not been tested for backflow protection. The central section of the valve incorporates a plastic strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 60°C.
Bistable (latching - pulse controlled) or monostable (normally closed) solenoid valve with a plastic body, EPDM diaphragm and ‘O’-rings. Maximum working pressure 10.0 bar. Hot water use only (70°C).
Normally closed (monostable) or latching (bistable) solenoid valve with a plastic body, EPDM membrane and ‘O’-rings, for insertion into specifically dimensioned bores. The inlet incorporates a plastic filter. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Latching solenoid valves with a plastic body and an EPDM diaphragm. The inlet incorporates a stainless-steel strainer. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Non-metallic materials and components comply with BS6920 at 65°C
Range of bistable solenoid valves with plastic bodies, incorporating chrome plated brass inlets and outlets, stainless steel springs, and EPDM diaphrams and ‘O’-rings. Maximum working pressure 10.0bar. Maximum operating temperature 65°C
Non-metallic materials and components comply with BS6920 at 65°C
Range of plastic solenoid valves with an EPDM membrane. 50.007.806.001 models incorporate a stainless steel strainer on the inlet. 50.007.806.003 models with a captive nut or ⅜” BSP (M) inlet incorporate a combined plastic washer and stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C (50.007.806.001 & 50.007.806.002 models) and 65°C (50.007.806.003 models).
Range of solenoid valves with plastic bodies and EPDM rubber diaphragms. The inlet incorporates an inner and outer plastic strainer, EPDM washer and a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Range of solenoid valves with plastic bodies and EPDM diaphragms. The FD-160A, FD-160Z, FD-160B and FD-160P have brass inlet and outlets. The FD-138 and FD-160 prefix models incorporate a stainless steel strainers on the inlet. Maximum working pressure 8.0 bar. Maximum operating temperature 65°C.
Range of latching solenoid valves with plastic bodies. Maximum working pressure 10.0 bar. Maximum operating temperature 80°C.
Non-metallic materials and components comply with BS6920 at 80°C
Solenoid valve with a plastic body, EPDM diaphragm and ‘O’-rings. The inlet incorporates a stainless steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 70°C
Solenoid valve with a plastic body, incorporating an EPDM diaphram and EPDM sealing rings. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of normally closed solenoid valves with black or grey plastic bodfies, EPDM diaphragm and EPDM ‘O’-rings. The inlet incorporates a removable plastic strainer with a stainless steel mesh. The outlet incorporates a plastic flow regulator. Maximum working pressure 10.0 bar. Cold water use only.
Range of normally closed solenoid valves with plastic bodies and silicone diaphragms. Model DSVP12N-12LSX-240M has two inlets. Maximum working pressure 0.060 bar. Cold water use only.
Range of normally closed solenoid valves with plastic bodies, EPDM ‘O’-rings and diaphragm. The inlet incorporates a combined plastic filter and stainless-steel strainer. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of solenoid valves with plastic bodies and silicone membrane. Maximum working pressure 8.0 Bar. Maximum operating temperature 65°C.
Non-metallic materials and components comply with BS6920 at 65°C
Range of plastic solenoid valves with an EPDM diaphragm and ‘O’-rings. The inlets incorporate a stainless-steel strainer (except for push fit inlet models). Push fit connections are for use with copper pipe (manufactured to EN 1057). Maximum working pressure 10.0 bar. Maximum operating temperature 70°C. BS6920 70°C.
Solenoid valve with a plastic body, EPDM diaphragm and ‘O’-rings. Maximum working pressure 8.0 bar. Can only be used with water at 70°C. BS6920 70°C.
Page of 1
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
