Section Code 1535 : Tap accessories.
Back To Directory SectionsRange of chromium plated, click type pop-up wastes, incorporating a silicone sealing washer.
Concealed, floor mounting basic set with DZR brass body for use with floor standing bath mixers. Maximum working pressure 5.0 bar. Maximum operating temperature 70°C.
INTINCT Range of chromium plated, click type pop-up wastes, incorporating a silicone sealing washer.
ESTEEM Range of chromium plated, click type pop-up wastes, incorporating a silicone sealing washer.
Wall mounted bracket hand shower inlet assemblies having a brass body (chromium plated brass) Maximum operating temperature 60°C
Click type pop-up wastes with chromium plated brass (W003 & W007 models) or zinc (W033 model) bodies and a silicone seal. Models (W003, W033) also have a matte black finish and model (W003) has a brushed nickel finish. Supplied with a metal or plastic backnut.
Combined bath filler and overflow waste assembly incorporating a manual operated pop-up waste using a dome type operating member. The inlet incorporates an approved single check valve cartridge however, the complete product has not been fully tested to demonstrate It provides backflow protection. Maximum operating temperature 60°C.
Range of rim and tile mounted bath basic sets, comprising of plastic chambers incorporating either a pull-out corrugated TPSiV lined shower hose with black outer sheath (28 010 xxx, 28 012 xxx, 28 020 xxx, 28 022 xxx models) or an integral stainless steel braided, silicone lined flexible hose assembly (13560180 and 15490180 models). The 28 010 xxx, 28 012 xxx, 28 020 xxx, 28 022 xxx models are supplied with finish sets in various finishes. The 28 010 xxx, 28 012 xxx, 28 020 xxx, 28 022 xxx models incorporate an approved check valve cartridge on each inlet, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 70°C
Surface mounting kit for a mono block sink mixer with stainless steel braided EPDM lined flexible hose assembly with ½” captive nut end connections.The product is supplied with a 15x15mm compression single check valve assembly (suitable for backflow protection against Fluid Category 2) which also incorporates an isolation valve, intended for installation at each inlet. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Range of chromium plated, click type pop-up wastes, incorporating a silicone sealing washer.
Coin type wastes with chromium plated brass body and rubber seal. Supplied with a plastic backnut.
Wall mounted shower arm with brass body (various finishes). Maximum operating temperature 85°C.
Ceiling mounted shower arm with brass bodies (various finishes) and faceplate. Maximum operating temperature 85°C.
In-wall concealed, manually accessible and operated hose connector incorporating a brass body, quarter turn ceramic disc headwork and operated by removable key. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of bidet spray kits comprising of a hand set with self-closing trigger, wall bracket and EPDM lined, brass interlocked flexible hose assembly. Maximum working pressure 5.0 bar. Maximum operating temperature 60ºC.
Range of isolation valves incorporating brass bodies and EPDM ‘O’-rings. Maximum working pressure 5.0 bar. Maximum operating temperature 60°C.
Tap outlet with a silicone body. Maximum operating temperature 100°C.
Chrome plated brass quick connector with EPDM washer. Maximum operating temperature 60°C.
Range of bidet spray kits comprising of a hand set with self-closing trigger, wall bracket, flexible hose assembly, thermostatic blending valve and isolation valve. Maximum working pressure 5 bar. Maximum working temperature 60°C
Angle bracket with brass body (various finishes). The inlet incorporates an approved check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of spout outlets with brass bodies (various finishes) incorporating an aerator. Product is supplied with either a lever type pop up (HIRONDELLE models) or click type waste (ICON-X & CORVAIR models). Maximum working pressure 3.5 bar. Maximum operating temperature 60°C.
Spout end flow control device (aerator with ‘switchable’ spray formation). Maximum operating temperature 65°C.
Range of brass (chrome plated) quick fit connectors. Maximum operating temperature 60°C
Range of click type pop-up wastes with brass bodies. Maximum operating temperature 60°C.
Range of installation kits with brass bodies. Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of brass (chrome plated) quick fit connectors. Maximum operating temperature 60°C
Wall mounted shower outlet elbow with a chromium plated brass body incorporating EPDM ‘O’-rings. The outlet incorporates an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum operating temperature 60°C.
A range of spray handsets (chrome plated plastic bodies). The outlet incorporates a plastic aerator.
Non-metallic materials and components comply with BS6920 at 60°C
Hand spray outlet (chrome plated brass body) with a self-closing trigger assembly. Maximum working pressure 10.0 bar.
Non-metallic materials and components comply with BS6920 at 65°C
Range of tap outlets with plastic bodies incorporating a filter within the body with a hollow fibre filter membrane The filters are supplied with (and must be used with) a chrome plated brass adapter which incorporates a plastic flow regulator. Open outlet use only.
Non-metallic materials and components comply with BS6920 at 60°C
Range of pull-out spray assemblies with a flexible hose and a self-closing trigger. Maximum working pressure 10.0 bar. Cold water use only.
Range of wall mounted installation kits with brass bodies Maximum working pressure 5.0 bar
Non-metallic materials and components comply with BS6920 at 85°C
PET braided, PE/EPDM lined ‘Motion hose’, available in a range of lengths. Maximum operating temperature 70°C.
Pull-out hose assembly consisting of a chromium plated brass 45° elbow connector, a chromium plated brass HDPE lined shower hose and a nylon braided HDPE lined connecting hose. Maximum operating temperature 65°C.
Concealed wall mounted rough inset with a brass body, incorporating EDPM O-rings. Maximum working pressure 5.0 Bar
Non-metallic materials and components comply with BS6920 at 85°C
Range wall mounted elbows (XX 1799 YY & XX E 1799 YY) and compression (XX 1749 YY & XX 1825 YY) fittings with brass bodies (various finishes, see models). Open outlet use only.
Non-metallic materials and components comply with BS6920 at 65°C
Range of wall mounted installation kits with plastic bodies. Maximum working pressure: 10.0 bar
Non-metallic materials and components comply with BS6920 at 65°C
Three hole, basic rough-in set with a brass body, incorporating EPDM O-ring seals. The product is supplied with a shower hose and a stainless steel braided, silicone lined flexible connecting hose. Maximum working pressure 10.0 Bar
Non-metallic materials and components comply with BS6920 at 70°C
Range of concealed, wall mounted rough sets with DZR brass bodies. Maximum working pressure 10.0 Bar. Maximum operating temperature 75.0°C.
Range of ancillary inlet connections with brass bodies (various finishes, see models). Model PSH036 is deck mounted. Models PSH039 & PSH045 are wall mounted. Maximum working pressure: 5 bar. Maximum operating temperature: 85°C.
Range of ancillary connections with brass bodies (various finishes). Maximum working pressure 5.0 bar. Maximum operating temperature 85°C.
Range of hoses with EPDM, PVC or PEX inner tubes and a corrugated stainless-steel tube. The outlets incorporate a plastic aerator. Maximum operating temperature 65°C, open outlet use.
Page of 1
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.