Section Code 1180 : Couplings. Unless specified in the individual approval, the products within this section are not suitable for below ground use
Back To Directory Sections‘Tectite 316’ range of push-fit fittings with stainless steel bodies incorporating EPDM ‘O’-rings for use with stainless steel tube (Grade 316 manufactured to EN 10312). Maximum working pressure and operating temperatures: Fittings up to and including 28mm: 20.0 bar @ 30°C, 16.0 bar @ 65°C, 10.0 bar @ 100°C. Fittings over 35mm: 16.0 bar @ 30°C, 10.0 bar @ 65°C, 6.0 bar @ 100°C.
Range of brass push-fit fittings incorporating EDPM O-rings. For use with Irish copper pipe Maximum working pressure 16.0 bar. Cold water use only.
Range of Twistloc push-fit fittings with PEX or polysulphone bodies incorporating EPDM ‘O’-rings. The fittings are supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part part 2) and copper pipe. Maximum working pressure and operating temperature: 3.0 bar@92°C, 4.0 bar@82°C & 12.5 bar@20°C.
‘VSH SudoPress’ range of copper or gunmetal press-fit fittings with EPDM ‘O’ rings for use with copper pipe. Joints are achieved by the use of a press fitting tool. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
>B< Sonic range of Brass & Copper push fit fittings incorporating EPDM rubber ‘O’-rings for use with copper pipe. Above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
“B Profile SS” range of 316L & 304 stainless steel press fittings with EPDM ‘O’-rings for use with stainless steel pipe manufactured to EN 10312. Joints are achieved by the use of a press fitting tool. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Flomasta push-fit fittings with PEX or polysulphone bodies incorporating EPDM ‘O’-rings. The fittings are supplied with polysulphone inserts. For use with PEX pipe (manufactured to BSEN 7291 part 3), PB (manufactured to BSEN 7291 part part 2) and copper pipe. Maximum working pressure and operating temperature: 3.0 bar@92°C, 4.0 bar@82°C & 12.5 bar@20°C.
Tectite Classic and Tectite Pro ranges of DZR brass push-fit fittings The Tectite Classic range is for use with copper tube (manufactured to BS 2871) and PEX & polybutylene tube (manufactured to BS 2871). The fittings are supplied with plastic inserts. The Tectite Pro range is for use with copper tube (manufactured to BS 2871). Maximum working pressures & operating temperatures: Tectite Classic fittings with copper pipe: 16.0 bar @ 30°C, 10.0 bar @ 65°C & 6.0 bar @ 95°C. Tectite Classic fittings with PEX & Polybutylene: 12.0 bar @ 20°C, 6.0 bar @ 65°C & 3.0 bar @ 92°C. Tectite Pro fittings (15mm - 28mm): 20.0 bar @ 30°C, 16.0 bar @ 65°C & 10.0 bar 114°C. Tectite Pro fittings (32mm - 54mm): 16.0 @ 30°C, 10.0 bar 65°C & 6.0 bar @ 90°C.
Profipress & Sanpress ranges of gunmetal, copper or bronze (press-fit) fittings, with EPDM `O` rings. For use with copper tube (manufactured to BS EN 1057). Sizes 64mm – 108mm incorporate a stainless-steel grab ring. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Press-Inox range of stainless-steel crimped fittings with EPDM ‘O’ rings for use with stainless steel pipe (manufactured to EN10204). For above ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C
Range of R-154 stainless steel pressed collars incorporating stainless steel bodies and are only to be used with stainless steel pipe. Maximum working pressure for sizes up to DN150 is 25.0 bar. Maximum working pressure for size DN200 is 16.0 bar. Maximum operating temperature 99°C
Range of metric black, white or grey DMFit plastic pushfit fittings with EPDM ‘O’-rings for use with metric PEX barrier pipe manufactured to BS7291-2. Supplied with grey pipe inserts. Maximum operating parameters: 12.0 bar @cold water use only and 7.0 bar @ 65°C
Range of copper crimped fittings with EPDM ‘O’-rings (except for 149ENM, 303ENM and 304ENM models) for use with copper pipe. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of push-fit fittings with polypropylene bodies and NBR seals for use with copper, BS7291 polybutylene and PEX pipe. Cold water use only. Maximum working pressure 16.0 bar.
Range of brass Pushtite fittings incorporating EDPM O-rings. For use with Irish copper pipe Maximum working pressure 16.0 bar. Cold water use only.
Fluidfit range of black, grey and white push-fit fittings with plastic bodies, incorporating EPDM ‘O’ rings. For use with LLDPE tube (manufactured to DIN 8072). Maximum working pressures: 4 - 8mm & 5/32” - 5/16” models = 16.0 bar. 10 – 12mm & ⅜” – ½” = 10.0 bar. Cold water use only.
Archung series, ‘N.U’ range of S30408 & S31603 stainless steel crimp fit fittings with EPDM ‘O’-rings, for use with stainless steel pipe manufactured to EN10312. Joints are achieved by the use of a press fitting tool. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of Victaulic clamps with EPDM rubber gaskets. Products in ‘Style 905’ are for use with plain end HDPE pipe and products in ‘Style 907’ are for use with HDPE and steel pipe (EN 10217-1). For above and below ground use. Pressure ratings SDR 7.4(PN25), SDR 11(PN16), & SDR17(PN10). Cold water use only.
Range of fittings for use with pressure gauges, having nickel plated brass bodies and EPDM ‘o’ rings where applicable. Maximum working pressure: Kee Push fit – 10.0 bar, Kee 050 plug, Kee T Piece, Kee 050 coupler – 35.0 bar. Cold water use only.
Range of press-fit fittings with brass bodies and EPDM `O`-rings for use with copper pipe manufactured in accordance with EN1057. Maximum working pressure 16.0 bar (sizes 12mm to 34mm). Maximum working pressure 10.0 bar (sizes 35mm to 54mm). Maximum operating temperature 90°C.
Range of DZR brass push fit fittings for use with copper pipe, PB pipe (manufactured to BS7291-2) & PEX pipe (manufactured to BS7291-3). When used with copper pipes the maximum working pressure is 16.0 bar. When used with plastic pipes the maximum working pressure is 6.0 bar. Maximum operating temperature 95°C.
‘EPH_WSP19’ Range of brass bodied fittings for use with copper pipe, some fittings are to be soldered with copper pipe (see models). Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
Range of rigid ductile iron couplings (copper colored alkyd enamel) (Style 606-EN), Vic-flange adapter’s (Style 641-EN) and grooved copper fittings (No. 610, 611, 620, 625, 650 & 660 –EN) for use with grooved copper tubing (manufactured to EN 1057 R250). Above ground use only. Maximum working pressure 10.0 bar. Maximum operating temperature 65°C.
Fluidfit range of hose barb fittings/stem fittings with push fit connections. Also with EPDM ‘O’-rings. 12 & 15mm models are for use with LLDPE pipe, 22mm models are for use with PEX pipe. Cold water use only Maximum working pressure 10.0 Bar
‘EPH_WSP19’ Range of brass bodied fittings for use with copper pipe, some fittings are to be soldered with copper pipe (see models). Maximum working pressure 10.0 Bar. Maximum operating temperature 85°C.
“Plimat ABS Fittings BS Inch and ABS Adaptor Fittings” range of ABS solvent cement or threaded fittings for use with “Plimat ABS pipe”. Maximum working pressure: 15.0 bar (fittings with ½” - 4” solvent cement connections), 9.0 bar (fittings with 5” or 6” solvent cement connections, with or without threaded connecitons), and 10.0 bar (fittings with threaded connections and ½” - 4” solvent cement connections). Cold water and above ground use only.
Range of PSU, POM & DZR brass pushfit fittings for use with PE-x pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) & copper pipe. Maximum working pressure 10.0 bar @ 65°C (PSU & DZR Brass Fittings). Open outlet use only @ 20°C (POM Fittings).
Range of press fittings incorporating copper or copper alloy bodies and EPDM O’-rings for use with copper tube to EN1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of Flomasta brass pushfit fittings for use with PE-x pipe (manufactured to BS7291-3), PB pipe (manufactured to BS7291-2) & copper pipe. Maximum working pressure 10.0 bar @ 65°C (PSU & DZR Brass Fittings). Open outlet use only @ 20°C (POM Fittings).
Range of copper crimped fittings with EPDM ‘O’-rings (except for 28171 & 28173 models) for use with copper pipe. The 27897 & 27898 models added May 2022 are for use with copper pipe manufactured to EN 1057. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of press fittings with a stainless steel body and EPDM ‘O’ rings for use with stainless steel 316L pipe manufactured to EN10312. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of polypropylene push-fit fittings and inserts for use with MDPE pipe (manufactured to BS EN 12201). For above and below ground use. Maximum working pressure 16.0 bar. Cold water use only.
Range of polypropylene push-fit fittings with inserts for use with MDPE Pipe (manufactured to BS EN 12201-2) on one side of the fitting and PB (BS 7291), PEX (BS 7291) or Copper (BS EN 1057) on the other. Models UTS147-DB, UTS197-DB & UTS251-DB are for above and below ground use. All other models are for above ground use only. Maximum working pressure when using 20mm pipe is 16.0 bar. Maximum working pressure when using 25mm & 32mm pipe is 12.5 bar. Cold water use only.
Range of brass press fittings with EPDM ‘O’-rings for use with EN ISO 21003 pipe. Maximum working pressure 10.0 bar. For cold water use only.
Range of crimp fittings with a bronze body incorporating EPDM O-rings. For use with copper pipe manufactured to EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C
Range of SUS316L & SUS304 stainless steel press fittings for use with stainless steel pipe manufactured to EN 10312. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of press fit fittings incorporating copper (GP5 models) or bronze (GP4 models) bodies and EPDM `O`-rings, for use with copper tube to EN 1057. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Unidelta range of compression fittings with polypropylene bodies with EPDM ‘O’ rings for use with PE100 polyethylene pipe (manufactured to EN12201). Maximum working pressure 16.0 bar. Cold water use only.
Range of copper press fittings with EPDM rubber ‘O’-rings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of M type press fittings with TP2 copper bodies and EPDM ‘O’-rings, for use with TP2 copper pipe to EN1057. Above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of press-fit end connectors (gunmetal bodies) for use with copper pipe manufactured to BS EN 1057. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of brass tee fittings for use with copper pipe to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘HE-705X & HE-715X’ ranges of brass crimp fit fittings incorporating EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057-2006). HE-7052/7053/7058/7059 & HE-7152/7153/7158/7159 models also incorporate a NBR gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
VSH XPRESS Range of copper press fittings with EPDM rubber ‘O’-rings for use with copper pipe (manufactured to EN 1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of PVC-u solvent weld and threaded union fittings incorporating an EPDM ‘O’-ring. For use with PVC-u pipe manufactured to ISO 1452 and DIN 8063. Maximum working pressure 10.0 bar. Cold water use only.
‘Xpress’ range of press fit fittings with copper or brass bodies and EPDM ‘O’-rings. For use with copper tube manufactured to EN1057. For above ground ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Pexal range of brass press fittings with EPDM ‘O’-rings for use with copper pipe EN1057. Model VS0171373 incorporates 90° copper elbow (chrome plated) Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
>B< Press range of stainless-steel SUS316L fittings for use with 316L stainless steel tube manufactured to EN10312. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘AF’ range of compression fittings with brass or chrome plated brass bodies for use with copper pipe (manufactured to EN1057). The AF14 and AF15 tap connector models incorporate an EPDM washer. Maximum working pressure 16.0 bar. Maximum working temperature 85˚C
Range of tee fittings incorporating DZR brass bodies (chrome plated) and approved single check valve cartridge, verified by test (suitable for backflow protection against Fluid Category 2) for use with copper pipe to EN1057. Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
‘Tectite Sprint’ range of pushfit fittings with copper or DZR brass bodies. 10mm, 15mm, 22mm & 28mm pushfit fittings are for use with copper pipe (manufactured to BS EN 1057) and polybutylene barrier pipe and cross linked PEX barrier pipe (manufactured to BS 7291). 35mm, 42mm & 54mm pushfit fittings are for use with copper pipe (manufactured to BS EN 1057) only. When used with PB & PEX pipes operating parameter are: 12.0 bar@cold water. 3.0 bar@92°C. When used with copper pipes operating parameter are: 20.0 bar@cold water. 10.0 bar@100°C.
Range of M type press fittings with TP2 copper bodies and EPDM ‘O’-rings, for use with TP2 copper pipe to EN1057. Above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘Instantor’ range of press-fit fittings incorporating DZR brass or Gunmetal bodies and EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum working temperature 95˚C.
Range of ‘StrengThin™’ 100 System couplings and fittings for use with stainless steel pipe (manufactured to EN 10217-7). For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 65°C.
Kuterlite K900 Pro range of compression fittings with DZR brass bodies for use with copper pipe (EN 1254) Maximum working pressure for 8mm-10mm = 70.0 bar. Maximum working pressure for 12mm – 28mm = 20.0 bar. Maximum working pressure for 35mm – 54mm = 6.0 bar. Maximum operating temperature 90°C.
Range of copper and DZR brass press fit tap connectors for use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of ductile iron pipe couplings for use with stainless steel and carbon steel pipe. The carbon steel pipe must incorporate a suitable coating or lining for wholesome water use. For maximum working pressure and the type of pipe the fittings are for use with, please refer to model. For above and below ground use. Maximum operating temperature 65°C.
Elysee range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of stainless steel (SS316L) pressfit fittings with EPDM ‘O’-rings for use with stainless steel pipe (manufactured to EN10312). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of stainless steel (SS316L) pressfit fittings with EPDM ‘O’-rings for use with stainless steel pipe (manufactured to EN10312). Maximum working pressure 16.0 bar. Maximum operating temperature 100°C.
Range of brass press fittings with EPDM ‘O’-rings for use with EN ISO 21003 pipe. Maximum working pressure 10.0 bar. For cold water use only.
STH Ranges of brass crimp fit fittings incorporating EPDM ‘O’-rings for use with copper pipe (manufactured to EN1057-2006). 74232, 74233, 74234, 74226, 74227, 74228, 74229 & 74231 models also incorporate a NBR gasket. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
Range of compression fittings with brass brass bodies for use with copper pipe (manufactured to EN1057). Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
‘KSO’ range of compression fittings with brass or chrome plated brass bodies for use with copper pipe (manufactured to EN1057). The KSO14 sand KSO15 tap connector models incorporate an EPDM washer. Maximum working pressure 16.0 bar. Maximum working temperature 85˚C
Timco - Elysee range of Polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Jason range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of black coloured, PE100 butt fusion fittings for use with PE100 pipes (manufactured to EN 12201). Maximum working pressure for fittings used with SDR11 pipe is 16.0 bar and for fittings used with SDR17 pipe is 10.0 bar. For above and below ground use. Cold water use only.
Henco Press Brass (P) and Henco Press Black coloured (PK) ranges of press fit fittings (brass or PVDF bodies) for use with Henco RIXc PEXc/Al/PEXc pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
Henco Schroef (EK) range of compression fitting (brass or PVDF bodies) for use with Henco RIXc PEXc/Al/PEXc pipes. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C.
‘Mapress’ range copper or copper and brass “copper-press” fittings with butyl rubber (up to 54mm) or EPDM rubber (>54mm) ‘O’-rings for use with copper pipe to BS EN 1057. For above ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Aquaflow range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of black polyethylene electrofusion fittings for use with PE100 pipe (manufactured to EN 12201-2). Please refer to model for maximum working pressures. For below ground and cold water use only.
Range of tank and cistern connectors, with push fittings. Models CM0715S and CM0722S are for use with copper tube (manufactured to BS EN 1057) PE-X pipe (BS7291-3) & PB pipe (BS7291-2). Until April 2023, model CM0728S was only for use with copper tube (manufactured to BS EN 1057). From May 2023, model CM0728S is also for use with PE-X pipe (BS7291-3) & PB pipe (BS7291-2). Cold water use only.
Range of ‘Superseal’ and ‘Speedfit’ push-fit fittings with acetal body’s (black or light grey) and NBR ‘O’ rings. For use with John Guest LLDPE tubing (Speedfit port only) and 316 stainless steel tubing manufactured to EN10088 (Superseal push-fit port only). Pipe inserts must be used for the LLDPE tube sizes 3/8” and ½”. Maximum working pressure: See models below. For cold water use only.
Range of press-fit fittings with stainless steel bodies incorporating EPDM ‘O’-rings for use with SS316L pipes. Maximum working pressure 16 bar.
Non-metallic materials and components comply with BS6920 at 85°C
Range of plastic push-fit fittings (available in black, white and grey) and a manifold (available in grey only) with EPDM or NBR ‘O’-rings. For use with copper pipe (manufactured to EN1057), PE-X pipe (manufactured to BS7291-3:2010) & PB pipe (BS EN 21003-2:2008). Maximum working pressure: 12.5 bar @ 20°C (Cold water use only). From September 2023 the products are suitable for 8.0 bar @ 65°C.
Range of compression fittings with brass bodies for use with copper pipe (EN1057). Above ground use only. Maximum working pressure 16 bar. Maximum operating temperature 85°C.
Range of “Effast” ABS fittings for use with ABS pipe complying with BS EN 5391-2006. Maximum working pressure: 15 Bar. Maximum operating temperature: 23°C.
Range of copper crimped fittings with EPDM ‘O’-rings (except for 149ENM, 303ENM and 304ENM models) for use with copper pipe. For above and below ground use. Maximum working pressure 16.0 bar. Maximum operating temperature 99°C.
Range of DZR brass push fit fittings for use with copper pipe (manufactured to BS EN 1057), PB pipe (manufactured to BS7291-2) and PEX pipe (manufactured to BS7291-3). Maximum working pressures and operating temperatures: 12.5 @ 20°C, and 3.0 bar @ 92ºC.
Range of press fittings with a stainless steel body and EPDM ‘O’ rings for use with stainless steel 316L pipe manufactured to EN10312. For above ground use only. Maximum working pressure 16.0 bar. Maximum operating temperature 85°C.
alpex Duo XS and alpex L (PPSU & Brass) ranges of press fittings for use with alpex Duo XS (F and TH press profiles) & alpex L pipe (F press profile only). Maximum working pressure 10.0 bar. The maximum operating temperature is 95oC.
PLAS-FIT range of polypropolene fittings for use with PE pipe (manufactured to EN 12201). Maximum working pressure 16 bar. Cold water use.
Range of Conex >B< press fittings incorporating copper & brass bodies for use with copper tube (manufactured to EN1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
‘Trustlene’ range of electrofusion and spigot fittings, with PE100 or brass bodies, for use with SDR11 PE100 pipe (manufactured to IS 4984: 2016). For use above and below ground. Maximum working pressure 16.0 bar. Cold water use only.
Range of Effast PVC-u solvent welded and/or threaded fittings for use with PVC-u pipe manufactured to (EN1452-2). Maximum working pressure 16.0 bar. Cold water use only.
Stainless steel press fittings incorporating EPDM ‘O’-rings for above ground use only. To be used with stainless steel 316L pipe (EN 10312). Maximum working pressure 10.0 bar. Maximum operating temperature 85°C.
Range of Talbot pushfit fittings with polyprolylene or acetal bodies and EPDM o-rings for use with MDPE PE80 pipe (BS EN 12201). For use above and below ground use. Maximum working pressure 16 bar. Cold water use only.
JG Speedfit range of push-fit fittings and manifolds for use with Polybutylene Barrier Pipe (manufactured to BS EN 7291-2:2010 ) and PEX Barrier Pipe (manufactured to BS EN 7291-3:2010) and Copper Pipe (manufactured to BS EN1057:). Operating parameters: 12.5 bar@20°C.
‘AquaGas M range’ of copper and brass press fit fittings with NBR ‘O’-rings for use with copper tube (manufactured to BS EN 1057). Maximum working pressure 16.0 bar.
Non-metallic materials and components comply with BS6920 at 85°C
‘SharkBite’ range of brass push fit fittings incorporating an EPDM ‘O’-ring. For use with the following pipes: JG Speedfit Layflat Polybutylene Barrier Pipe (JG BPB pipe manufactured to BS EN 7291-2:2010), 'BPEX' Barrier Pipe (JG BPEX pipe manufactured to BS EN 7291-3:2010), Polybutylene barrier pipe (manufactured to BS EN 7291-2:2010), PEX barrier pipe (manufactured to BS EN 7291-3:2010) and Copper pipe (manufactured to BS EN1057:2006). Maximum working pressures and operating temperatures: When used with Polybutylene barrier pipes (manufactured to BS EN 7291-2:2010) and PEX barrier pipes (manufactured to BS EN 7291-3:2010): 12.5 bar, cold water use only. 6.0 bar @ 95°C. When used with copper pipe (manufactured to BS EN1057:2006): 10mm sizes: Maximum working pressure 16.0 bar. Cold water use only. Maximum working pressure 10.0 bar. Maximum operating temperature 95°C. 15-22mm sizes: Maximum working pressure 20.0 bar. Cold water use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C. 28mm size added April 2024: Maximum working pressure 20.0 bar. Cold water use only. Maximum working pressure 16.0 bar. Maximum operating temperature 95°C.
‘Redman’ range of fittings with mild steel bodies and a black polyamide coating for use with PE-AL-PE barrier pipe (manufactured to BS 8588). Jointing is achieved by hydraulic compression. For above and below ground use. Maximum working pressures: 90mm - 180mm SDR 17 PE100 pipe system: 10.0 bar, 90mm - 180mm SDR 11 PE100 pipe system: 16.0 bar. Cold water use only.
IDC ‘BDGxxx’ range of press fittings with brass or nickel plated brass bodies (see model) incorporating EPDM ‘O’-rings and stainless steel crimp sleeves for use with PEX/AL/PEX multilayer pipe (manufactured to EN ISO 21003). The BDG241 and BDG257 prefix models incorporate an EPDM gasket on the captive nut end connection. Pressfit jointing is achieved by either a U or TH crimping profile. Compression connections are for use with copper pipe 12-28mm (manufactured to EN1057) or Irish copper pipe 14.7-27.4mm (manufactured to EN1057). For above ground use only. Maximum working pressure 10.0 bar. 20, 25 & 26mm pressfit sizes cold water use only. Threaded, compression and 16 & 32mm pressfit sizes maximum operating temperature 95°C.
MecFlow Press (PPSU & Brass) Ranges of press fittings for use with MecFlow Press pipes. Maximum working pressure 10.0 bar. The maximum operating temperature is 95oC.
Page of 1
We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.
