Hansgrohe SE Approvals


#2007054

Range of brass shower arms and plastic shower heads (various finishes) incorporating EPDM seals and ‘O’-rings, silicone seals and spray insert. The 26 469 xxx model is ceiling mounted & 26 470 xxx model is wall mounted. Both models incorporate a swivel joint housing a plastic flow regulator. Maximum operating temperature 60°C.

Section:
1650 Shower Outlets
WRAS Approval Number:
2007054
Expiry date:
31/07/2025
Note:
Open outlet use only. Claims for flow rate are made by the manufacturer and not considered part of the listing.
Size:
½” BSP (M)
Marking:
Hansgrohe on edge of body
Installation Requirements:
R001 R040
Model:
26 469 xxx HG Raindance Select S Overhead shower 240 2jet EcoSmart 9 l/min with ceiling connector. 26 470 xxx HG Raindance Select S Overhead shower 240 2jet EcoSmart 9 l/min with shower arm. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company

Print This Approval


#2007075

Range of single hole, single outlet (swivel) combination tap assemblies (various finishes), incorporating a ceramic cartridge headwork with a single lever operating member. The spout outlets incorporate a plastic aerator and an on/off button which can stop the flow of water. The inlets incorporate approved check valve cartridges, however, the complete product has not been fully tested to demonstrate it provides backflow protection Maximum working pressure 10.0 bar. Maximum operating temperature 70°C.

Section:
0470 Combination Tap Assemblies
Section Subtitle:
Single hole, metal, single outlet, swivel. Taps used in high risk installations, such as kitchen sinks, are considered to be a fluid category 5 risk. Backflow protection is usually provided in the form of an AUK3 tap gap. Where an AUK3 tap gap cannot be maintained, for example where the tap gap is compromised as a result of:- • the tap being lowered in any way; • adjustment to the spout which reduces the distance between the tap outlet and spillover level of the sink; • or the operation of a pull out hose attachment; alternative fluid category 5 backflow protection is required.
WRAS Approval Number:
2007075
Expiry date:
31/07/2025
Size:
Stainless steel braided PE-X lined flexible hose assemblies with ⅜” captive nut end connections.
Marking:
Hansgrohe on body.
Installation Requirements:
R001 R006 R009 R010
Model:
72 820 xxx 72 825 xxx 73 854 xxx Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company

Print This Approval


#2006046

Range of overhead wall mounted shower outlets with brass bodies (various finishes), incorporating a plastic aerator and stainless-steel strainers on two of the three inlets to the main body. The 35 283 xxx models also incorporate plastic flow regulators on all three of the inlets to the main body. Maximum operating temperature 60°C.

Section:
1650 Shower Outlets
WRAS Approval Number:
2006046
Expiry date:
30/06/2025
Note:
Open outlet use only. The iBox 01800180 rough-in (concealed) set is not approved in its own right. Claims of flow rate are made by the manufacturer and not considered part of the listing.
Size:
¾” BSP (F)
Marking:
Hansgrohe on spray plate. AXOR on spray plate (model 35 283 xxx)
Installation Requirements:
R001 R040
Model:
24 001 400 Hansgrohe Rainmaker Select 580 3jet overhead shower (white/chrome). 24 001 600 Hansgrohe Rainmaker Select 580 3jet overhead shower (black/chrome). 24 011 400 Hansgrohe Rainmaker Select 580 3jet overhead shower Ecosmart 9 l/min (white/chrome). 35 283 xxx AXOR ShowerSolutions Overhead shower 250/580 3jet. All the above items are for use in conjunction with the iBox 01800180 rough-in (concealed) set. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company

Print This Approval


#2009001

Range of wall mounted concealed manual blending valves with a DZR brass body incorporating a ceramic cartridge headwork with a single lever operating member, fitting is available with trim set (available in various finishes). Maximum working pressure 10.0 bar. Maximum working temperature 70°C.

Section:
2000 Valves
Section Subtitle:
Blending, manually operated.
WRAS Approval Number:
2009001
Expiry date:
30/09/2025
Note:
Rough in set 13 620 180 is not approved in its own right.
Size:
½” BSP (F)
Marking:
Hansgrohe on top of operating member. DR on body
Installation Requirements:
R001 R010 R040
Model:
31 686 xxx HG Metris 31 967 xxx HG Focus 71 606 xxx HG Logis 31 966 xxx HG Focus To be used with basic set 13 620 180 “xxx” denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and letters examples: 000= Chrome optic finish, 800= PVD Stainless steel optic finish
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company

Print This Approval


#2009002

Wall mounted two hole, single outlet (swivel) combination tap assembly with DZR brass bodies (various finishes). Incorporating a ceramic cartridge headwork and single lever operating members. The spout outlet incorporates a plastic aerator. Product is supplied with a pop-up waste. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
0510 Combination Tap Assemblies
Section Subtitle:
Two hole, metal, single outlet, fixed.
WRAS Approval Number:
2009002
Expiry date:
30/09/2025
Note:
For use with basic sets 13 622 180 (Models 34 112 xxx & 34 113 xxx) & 13 623 180 (Models 34 115 xxx & 34 116 xxx)
Size:
½” BSP (F)
Marking:
Axor (brand name of Hansgrohe) on spout
Installation Requirements:
R001 R010 R040
Model:
34 112 xxx AXOR Citterio M (167mm and plate) 34 113 xxx AXOR Citterio M (167mm and escutcheons) 34 115 xxx AXOR Citterio M (227mm and plate) 34 116 xxx AXOR Citterio M (227mm and escutcheons) Where xxx denote the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letter, as examples; 000 = chrome optic finish, 800 = PVD stainless steel optic finish
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company

Print This Approval


#2009007

Range of exposed wall mounted two-hole, single outlet (fixed) combination tap assemblies with brass bodies (various finishes), incorporating a two-way manual diverter controlling and diverting the flow between the spout outlet and an overhead shower (not supplied) and a single lever operating member. The temperature is controlled independently via a thermostatic cartridge with a single lever operating member incorporating a manual override button. The inlets incorporate a stainless steel strainer and an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. The spout outlet incorporates a plastic aerator. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
0520 Combination Tap Assemblies
Section Subtitle:
Two hole, metal, single outlet, fixed, manually operated diverter to shower outlet.
WRAS Approval Number:
2009007
Expiry date:
30/09/2025
Size:
½” BSP (M)
Marking:
Hansgrohe on front of body.
Installation Requirements:
R001 R010 R040
Model:
13 107 xxx Hansgrohe ShowerTablet 350 Exposed Thermostatic Bath Mixer 13 109 xxx Hansgrohe ShowerTablet 600 Exposed Thermostatic Bath Mixer Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
Factor:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company

Print This Approval


#2010002

Pillar tap with brass body (various finishes), incorporating a quarter turn ceramic disc headwork and cross top operating member. The spout outlet incorporates an aerator. Maximum working pressure 10.0 bar. Maximum operating temperature is 60°C.

Section:
1800 Taps
Section Subtitle:
Pillar, metal.
WRAS Approval Number:
2010002
Expiry date:
31/10/2025
Size:
3/8” (F) Compression
Marking:
AXOR on body.
Installation Requirements:
R001 R006
Model:
16 530 xxx AXOR Montreux Pillar tap 50 Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
Factor:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Kreuzwegstrasse 41 D-77656 Offenburg

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company

Print This Approval


#2009004

Range of ceramic cartridge headworks incorporating plastic bodies and silicone ‘O’-rings, to be inserted into specifically dimensioned bodies. Maximum working pressure 16.0 bar. Maximum operating temperature 70°C.

Section:
0440 Headworks
WRAS Approval Number:
2009004
Expiry date:
30/09/2025
Size:
25mm Ø
Marking:
HG on body
Installation Requirements:
R001
Model:
30 579 600 HG Mixing cartridge M25 30 122 100 HG Mixing cartridge M25L 30 122 101 HG Mixing cartridge M25LA Models added April 2021: 30 746 700 Cartridge M25LS 30 333 001 Cartridge M25LXS
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company

Print This Approval


#2011009

Thermostatic blending valve with brass body (various finishes), incorporating two push cartridges to control the water to the 2 outlets independently. The temperature is controlled also controlled independently via a thermostatic cartridge with a dome operating member incorporating a manual override button. Both inlets incorporate an approved check valve cartridge, however, the complete product has not been fully tested to demonstrate it provides backflow protection. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
2010 Valves
Section Subtitle:
Blending, thermostatic.
WRAS Approval Number:
2011009
Expiry date:
30/11/2025
Size:
¾” BSP (F)
Marking:
Hansgrohe on face plate.
Installation Requirements:
R001 R010 R040
Model:
15 765 xxx Hansgrohe ShowerSelect Thermostat Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters. As examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company

Print This Approval


#2011010

Three-hole, single outlet, fixed combination tap assembly with a brass body (various finishes), incorporating quarter turn ceramic disc headwork with single lever operating members. The spout outlets incorporate a plastic aerator and the products are supplied with lever type pop-up waste and metal backnuts. Maximum working pressure 10.0 bar. Maximum operating temperature 60°C.

Section:
0650 Combination Tap Assemblies
Section Subtitle:
Three hole, metal, single outlet, fixed.
WRAS Approval Number:
2011010
Expiry date:
30/11/2025
Size:
Stainless steel braided, thermoplastic silicone rubber (TPSiV) lined flexible hose with 3/8” BSP captive nut.
Marking:
Hansgrohe on body.
Installation Requirements:
R001 R006 R009 R010
Model:
31 073 xxx Hansgrohe Metris Classic 3-hole basin mixer 100 with pop-up waste set. Where xxx denotes the surface finish (which is a non-water contact part). It will always be 3 digits, which can be any combination of numbers and/or letters, as examples: 000 = chrome optic finish, 800 = PVD stainless steel optic finish.
Factor:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company
Manufacturer:
Hansgrohe SE
Company Name
Hansgrohe SE
Address
Auestrasse 5 - 9, 77761 Schiltach

View All Listings by this Company

Print This Approval



Back To Directory Sections

Page 10 of 41

We use cookies to give you the best possible experience with WRAS. Some are essential to provide website functions and ensure the website is secure. We also use cookies to help us understand how people use the site and to make improvements. Click "Accept All" to enable recommended settings or click "Manage cookies" to adjust your settings. For more details, see our Cookie Policy.